DIY 3D Printer Electronic Parts Really, I'm not out to destroy Microsoft. That will just be a completely unintentional side effect. - Linus Torvalds The creator of the Linux Open Source Operating System.
Phone Orders or Help: 800-734-3588, 206-458-7550 (Pacific Time)
spc Bd 1 Bd 3
 
Share This Page

DIY 3D Printer Electronic Parts

 

Having Trouble Ordering?

Please call:   800-734-3588     206-458-7550

Shipping Charges Too High?

We will refund your PayPal account.
Or you can for a correct PayPal invoice.

 

Nema 17 Stepper Motor XYZ

Manufacturer's Part Number 1124090

See Nema 17 Stepper Motor Diagram

  • High Torque: 5.5 kg-cm, 53.9 N-cm, 76 oz-in, 4.77 lb-in
  • 4.2 Volt, 1.5 Amp, 1.8 deg per step
  • 23 mm long, 5 mm Shaft with D Cut
  • Wires are 750 mm to the tip of the connector
  • Model: 42BYGH4803
  • 2 Phase
  • 200 Steps per Revolution
  • Resistance per Phase 2.8 Ohms
  • Inductance 4.8 mH
  • Class B Insulation
  • Kysan Electronics
  • DIY 3D Printer Electronic Parts DIY 3D Printer Electronic Parts
    1 / $16.65
    3 / $50.00
    4 / $65.00
    5 / $80.00

    Nema 17 Geared Stepper Motor

    Manufacturer's Part Number 1040229

    See Nema 17 Geared Stepper Motor Diagram

  • 42 mm
  • Gear Ratio: 5.18:1
  • 1830 mm Wire Connector
  • Wires are 1830 mm to the tip of the connector
  • 20 mm long, 8 mm Shaft with D Cut
  • Step Angle: 1.8°
  • Rated Voltage: 2.4 V
  • Rated Current: 1.0 A
  • 2 Phase
  • Inductance per Phase: 3.5 mH ±20% Phase
  • Resistance per Phase 2.4 Ohms ±10% Phase
  • Holding Torque: 2.2 Kg.cm
  • Class B Insulation
  • Diameter of the Geared Housing = 36 mm
  • Diameter of the Mounting Holes = 2 mm
  • Kysan Electronics
  • DIY 3D Printer Electronic Parts For Sale
    $33.95

    Vibration Dampers

    For use with Nema 17 stepper motors.

  • Significantly reduces noise, vibration and resonance problems commonly found in stepper motors
  • Robust but lightweight
  • Threaded mounting holes; can be mounted directly onto the motor flange
  • 2.2 mm access hole, large enough to accommodate a spigot and gear or pulley
  • 6 mm thick

  • Does not fit geared stepper motor
  • Steel and Rubber Vibration Dampers



    Manufacturer's Part Number MY17RMDAMP
    DIY 3D Printer Electronic Parts For Sale .


    Quantities 1, 3, 4, 5

    For use with Nema 17 stepper motors.

  • Helps reduces noise, vibration and resonance problems commonly found in stepper motors
  • Helps prevent thermal transfer from motor to plastic parts
  • Mounting holes; can be mounted directly onto the motor flange
  • 2.2 mm access hole, large enough to accommodate a spigot and gear or pulley
  • 3 mm thick

  • Does not fit geared stepper motor
  • Cork Vibration Dampers


    DIY 3D Printer Electronic Parts For Sale

    Quantities 1, 3, 4, 5

    Power Supply

    Mean Well Switching Power Supply

    Model: S-350-12

    Specifications

  • Manufacturer: Mean Well
  • Output Power: 348 W
  • Input Voltage: 90 VAC to 132 VAC, 254 VDC to 370 VDC
  • Number of Outputs: 1
  • Output Voltage-Channel 1: 12 V
  • Output Current-Channel 1: 29 A
  • 150 mV p-p Noise
  • 83 % efficient
  • 0.5 % Load Stability
  • Dimensions: 215mm x 115mm x 50mm
  • Mounting Style: Chassis

  • Data Sheet

    DIY 3D Printer Electronic Parts For Sale

    $39.95

    24 Volt 400W Wei Hao Single Output Power Supply

    Model: S-400-24

    Specifications

  • Manufacturer: Wei Hao (W H)
  • Single Output: 400W
  • 16.5 Amps at 24 V
  • 150 mV p-p Noise
  • 0.5 % Load Stability
  • Selectable by Switch
  • Dimensions: 215mm x 115mm x 50mm

  • Data Sheet

    DIY 3D Printer Electronic Parts

    $39.95

    Mean Well 150W Single Output with PFC Function

    Model MW SP-150 15

    Features

  • Universal AC input / Full range
  • Built-in active PFC function, PF>0.93
  • Protections: Short circuit / Overload / Over voltage / Over temperature
  • Built-in constant current limiting circuit
  • LED indicator for power on
  • LED indicator for power on
  • 100% full load burn-in test
  • Specifications

  • Manufacturer: Mean Well
  • 15V 150W
  • 10 Amps at 15 V
  • Noise: 100 mV p-p
  • Approvals: UL60950-1
  • Product: Switching Supplies
  • Open Frame/Enclosed: Enclosed
  • Output Power Rating: 150 W
  • Input Voltage: 90 VAC to 264 VAC, 254 VDC to 370 VDC
  • Number of Outputs: 1 Output
  • Output Voltage-Channel 1: 15 VDC
  • Commercial/Medical: Commercial
  • Mounting Style: Chassis
  • Dimensions: 179mm x 99mm x 45mm
  • Series: SP-150

  • Data Sheet

    DIY 3D Printer Electronic Parts For Sale

    $39.95



    LED

    Specifications

  • Quantity: 10
  • Size: 5mm
  • Wire Length: 20 cm
  • Forward Voltage: 12V/DC
  • Light Color: White
  • Picture Coming

    $5.95

    `

    Kapton Heater

      Specifications:
    • Lead Length: 1000 mm
    • Lead Wire: High Temperature Teflon
    • Lead Location: Center
    • Thermistor: 100K QWG-104F-3950 Preferred
    • Thermistor Location: Center with 1000 mm Leads
    • Resistance was measured at room temperature
    • 1 cm Hole in Center
    • Adhesive On Back
    Thermistor Specifications:

  • 100K Thermistor +/ 1 percent
  • B = 3950K

  • Operating Temp Range -35° C to 300° C
  • Item
    1-1
    Resistance
    Particulars
    Resistance
    AT25° C
    R25

    100K Ohm ±1%

    1-2 B
    Constant
    In(R25/R50)
    B= =(K)
    (T/T50-1/T25)

    R25/50

    3950K ±1%
    1-3
    Operating
    Temperature
    Range
        -35° C to 300° C

    24 v Kapton Heater - 400 mm Round

  • Size: 398 mm
    Use with 400 mm Borosilicate Glass
  • Voltage: 24
  • Watts: ~240
  • Amps: ~10
  • Resistance: ~2.9 ohms cold
  • Needs a heat spreader
  • DIY 3D Printer Electronic Parts For Sale
    Wires Included
    Need to be attached



    $44.95

    24 v Kapton Heater - 350 mm Round

  • Size: 348 mm
    Use with 350 mm Borosilicate Glass
  • Voltage: 24
  • Watts: ~240
  • Amps: ~10
  • Resistance: ~2.9 ohms cold
  • Needs a heat spreader
  • DIY 3D Printer Electronic Parts For Sale
    Wires Included
    Need to be attached



    $39.95

    24 v Kapton Heater - 300 mm Round

  • Size: 298 mm
    Use with 300 mm Borosilicate Glass
  • Voltage: 24
  • Watts: ~240
  • Amps: ~10
  • Resistance: ~2.9 ohms cold
  • Needs a heat spreader
  • DIY 3D Printer Electronic Parts For Sale
    $34.95

    24 v Kapton Heater - 240 mm Round

  • Size: 240 mm
    Use with 250 mm Borosilicate Glass
  • Voltage: 24
  • Watts: ~240
  • Amps: ~10
  • Resistance: ~2.9 ohms cold
  • DIY 3D Printer Electronic Parts
    $29.95

    12 v Kapton Heater - 240 mm Round

  • Size: 240 mm
    Use with 250 mm Borosilicate Glass
  • Voltage: 12
  • Watts: ~120
  • Amps: ~10
  • Resistance: ~1.2 ohms cold
  • DIY 3D Printer Electronic Parts For Sale
    $29.95

    24 v Kapton Heater - 160 mm Round

  • Size: 160 mm
    Use with 170 mm Borosilicate Glass
  • Voltage: 24
  • Watts: ~240
  • Amps: ~10
  • Resistance: ~2.9 ohms cold
  • DIY 3D Printer Electronic Parts
    $24.95

    12 v Kapton Heater - 160 mm Round

  • Size: 160 mm
    Use with 170 mm Borosilicate Glass
  • Voltage: 12
  • Watts: ~120
  • Resistance: ~1.2 ohms cold
  • DIY 3D Printer Electronic Parts For Sale
    $24.95

    Cork Heated Bed Insulator

      Specifications:
    • 170 mm diameter
    • 2 1/2 mm thick
    • Adhesive back
    Picture Coming

    $9.95

    Aluminum Heat Spreaders

    199 mm x 213 mm

    Picture Coming
    $11.95

    168 mm Round

    Picture Coming
    $11.95

    248 mm Round

    Picture Coming
    $16.95

    298 mm Round

    Picture Coming
    $21.95

    348 mm Round

    Picture Coming
    $26.95

    398 mm Round

    Picture Coming
    $32.95

    FSR - Force Sensitive Resistor

    Description
  • Varies its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance
  • When no pressure is being applied to the FSR, its resistance will be larger than 1M Ohm
  • Can sense applied force in the range of 100g-10kg

  • Two pins extend from the bottom of the sensor
  • 0.1" pitch
  • Bread board friendly
  • Peel-and-stick rubber backing on the other side of the sensing area to mount the FSR
  • Long Tail

    DIY 3D Printer Electronic Parts

    1 / $6.95
    2 / $13.50
    3 / $19.95
    4 / $25.25
    5 / $29.95

  • Tail: 1.75"
  • Overall length: 2.375"
  • Overall width: 0.75"
  • Sensing diameter: 0.5"
  • Short Tail

    Diagram

    DIY 3D Printer Electronic Parts

    1 / $6.95
    2 / $13.50
    3 / $19.95
    4 / $25.25
    5 / $29.95

  • Tails: 0.5"
  • Overall length: 1.25"
  • Overall width: 0.75"
  • Sensing diameter: 0.5"
  • Board - FSR Endstop Controller

    By John SL

    Version 1.2
    Dimensions: 1 1/8" x 1"

    For more information, see FSR Endstop Controller.
    DIY 3D Printer Electronic Parts

    $10.00

    FSR Endstop Controller Kit

    DIY 3D Printer Electronic Parts DIY 3D Printer Electronic Parts

    Contains:

    (3) Long Tail FRSs
    (1) FSR Endstop Controller

    $29.95

    DIY 3D Printer Electronic Parts For Sale DIY 3D Printer Electronic Parts

    Contains:

    (3) Short Tail FRSs
    (1) FSR Endstop Controller

    $29.95

    End Stops, Limit Switch

    DIY 3D Printer Electronic Parts
  • SPDT
  • Single Pole
  • 19.8 x 10.2 x 6.4 mm (0.78" x 0.40" x 0.25")
  • 125/30 VAC/VDC
  • 10.1 A @ 125 VAC/250 VAC
  • 10.1 A @ 8 VDC/14 VDC
  • 4 A @ 30 VDC
  • 150 g operating force
  • 2.4 mm hole size
  • UL
  • CSA Certified
  • 30 Million Operations Minimum
  • End Stop, Limit Switch

    Switch Pin Plunger
    10.2 mm with Mtg Holes

    Manufacturer Part Number: SS-5


    2 / $5.50



    3 / $6.95



    4 / $7.95

    Wiring

    DIY 3D Printer Electronic Parts
  • Molex 2510 / 2510T compatible pin connectors
  • Compatible with PrintrBoard Electronics
  • Ends are pre-stripped and tinned
  • 0.100" centers
  • Female connectors for Printrboard
  • 600 mm total length (wire + connector)
  • 2 Pin 4 / $5.95

    Out of Stock
    3 Pin 3 / $5.95

    Out of Stock
    4 Pin 3 / $5.95

    Out of Stock

    Wiring Components - Connectors

    DIY 3D Printer Electronic Parts
  • Molex 2510/2510-T Compatible
  • 0.100" centers
  • For Printrboard
  • Female
  • 2 Pin 10 / $4.95

    3 Pin 10 / $4.95

    4 Pin 10 / $4.95

    Wiring Components - Crimp Pins

    DIY 3D Printer Electronic Parts For Sale Molex 2510/2510-T Compatible

    100 / $5.95

    Teflon Coated Wire

    DIY 3D Printer Electronic Parts
  • Can Withstand High Heat
  • Voltage Rating: 600 Volts
  • Insulation Material: Teflon
  • 19 Strands
  • Wire Gauge: 16 AWG

  • M16878 / 4BJE9
  • Choose Color (White/Black)
  • 1 meter / $5.95

    Wire Gauge: 18 AWG

  • Conductors: 1
  • Mil-W-16878/4 (Type E)
    200C 600 V RMS
  • Choose Color (Green/Yellow)
  • 1 meter / $5.95

    Silicone Rubber Coated Wire

  • Red
  • 18 AWG
  • 150° C
  • TV-3
  • ATX 12 Volt Power Connector and Crimp Pins

    DIY 3D Printer Electronic Parts For Sale

  • Use to connect power to PrintrBoard
  • Not needed if PC power supply has a 12 volt connector
  • Includes
    • 2 Connectors
    • 10 Crimp Pins
    $4.95

    USBtinyISP Programmer with USB Cable

    DIY 3D Printer Electronic Parts For Sale $17.95

    Open source v3 USB AVR programmer and SPI interface

    Works with AVRdude

    AVRStudio compatible for use with Windows, Linux, and Mac OS X

    Based off of the USBtiny design that has been improved to use the SpokePOV interface

    Includes:

  • Fully functioning pre-programmed USBtinyISP v3 board
  • USB cable
  • 10 pin programming cable
  • 6 pin programming cable

  • Easy to use:

  • AVRdude compatible
  • USB drivers available for Windows using libusb. No driver needed for Mac OS X or Linux
  • Power/USB good LED
  • Busy LED
  • Buffered I/O for variable voltage targets 2V-6V (Remember to take out the 5 volt power jumper)

  • Easy to power:

  • Can use USB power if less than 100mA is required
  • 5V Power jumper allows the cable to power the target
  • With the 5v power jumper removed, the USBtinyISP is self powered and buffers the I/O to match the target device
  • SanDisk Micro SD Memory Card
    with Adaptor and Plastic Case

    Class 4 - 8GB

    Required for Azteeg X5
    DIY 3D Printer Electronic Parts For Sale
    $8.95

     

    Home 3D Printer Basics Build Instructions 3D Printer Models Filament Basics Compare Filaments Fun Reading 3D Printer Patents

    Store



    BOM (Parts List)



      Kossel Mini
      BOM (Parts List)

      Kossel Legacy
      BOM (Parts List)

      Prusa i3 Rework
      BOM (Parts List)


    Electronics   Stepper Motors   Power Supplies   Stepper Motor Dampers   Kapton Heaters   Azteeg X5 Instructions   USBtinyISP   FSR/Endstop Controller   Limit Switches
      End Stops
      Wiring,
      Connectors, Crimps
      Power Connector
    Plastic Parts
    Mechanical Parts   Belts & Gears   Bearings   Coupling   Kossel Nuts
      Bolts, Screw
      Rods (Arms)   Rod Ends   Rod Set Screws   Hobbed Drive
      Gear
      Spool   Fan
    Kapton Heater
    Heat Spreader
    Borosilicate Glass

    Hot Ends   E3D HotEnds   E3D HotEnd Volcano   E3D HotEnd Nozzles   J Head
      HotEnds
      Resistors
      5.6, 6.8 Ohm
      Thermistors   Push Fit   Teflon Tube, PTFE
    Printing Supplies   Kapton Tape   Blue Tape
    Misc   Thermal Fuse   Heatbed   Extrusions   Silica Gel   Comm Cable   Spectra Line   Techflex   Split Loom
    T-Slot Aluminum Extrusions
    Bulk Nuts, Bolts, Screws

     


    Fun
    Optical Illusions

    We have free optical illusions. See how the brain and optical illusions work.
    Get the Explanation
    for this
    Optical Illusion

    Send Us Your Comments Share Site With A Friend Go To Our Site Map Link To Us Related Links

    Report A Broken Link Contact Information







    Tri  D
    Printing









































































































































































































































































































































































































































































































































    s_10






    s_11






    s_12
    B7
     
    TriDPrinting.com

    Site Map | Terms of Use | Privacy & Security | Contact Us | Purchase Agreement | Send Feedback
    DIY 3D Printer One Stop Shopping
    © 1996-2011 by TriDPrinting.com All Rights Reserved.